I setup a new Splunk receiver today. Setup a TCP listenner on 9993, wasn't sure what sourceType so selected Syslog, then setup a new index called WinEvents. Then I installed UF on separate Windows host and configured it to forward all events to SplunkServer:9993/TCP
I'm not sure why all events appear like this... is syslog the wrong sourceType?
-splunk-cooked-mode-v3--\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x008090\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00\x00@\x00\x00\x00\x1\x00\x00\x00\x13__s2s_capabilities\x00\x00\x00\x00\x14ack=0;compression=0\x00\x00\x00\x00\x00\x00\x00\x00\x5_raw\x00
host=myhostname Options| sourcetype=syslog Options| source=tcp:9993 Options
Found the problem/solution.
I had created the TCP listener using the WebUI incorrectly.
I started by clicking on: Data Inputs > TCP > etc.
Where I should have started is :
Forwarding and Receiving > Configure Receiving > New
The difference in these two starting points is the resulting entry in the inputs.conf file mentioned here:
http://answers.splunk.com/questions/10346/splunk-is-adding-weird-strings-like-linebreaker-x00-x00-to...
Found the problem/solution.
I had created the TCP listener using the WebUI incorrectly.
I started by clicking on: Data Inputs > TCP > etc.
Where I should have started is :
Forwarding and Receiving > Configure Receiving > New
The difference in these two starting points is the resulting entry in the inputs.conf file mentioned here:
http://answers.splunk.com/questions/10346/splunk-is-adding-weird-strings-like-linebreaker-x00-x00-to...